t330p www.vishay.com vishay semiconductors rev. 1.2, 22-may-14 1 document number: 83490 for technical questions, contact: optochipsupport@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 silicon pin photodiode description t330p chip is a pin photodiode with 0.23 mm 2 sensitive area, high speed and high photo sensitivity. it is sensitive to the visible and near infrared light spectrum with a peak sensitivity at 900 nm. anode is the bond pad on top, cathode is the backside contact. features ? package type: chip ? package form: single chip ? dimensions (l x w x h in mm): 0.67 x 0.67 x 0.28 ? wafer diameter (in mm): 100 ? radiant sensitive area (in mm 2 ): 0.23 ? peak sensitivity wavelength: 900 nm ? high photo sensitivity ? high radiant sensitivity ? suitable for visible light and near infrared radiation ? fast response times ? angle of half sensitivity: ? = 60 ? material categorization: fo r definitions of compliance please see www.vishay.com/doc?99912 applications ? high speed photo detector general information the datasheet is based on vishay optoel ectronics sample testing under certain predetermined and assumed conditions, and is provided for illustration purpose only. customers are encouraged to perform testing in actual proposed packaged and used conditions. vishay optoelectronics die products are tested us ing vishay optoelectronics base d quality assurance procedures and are manufactured using vishay optoelectronics established pr ocesses. estimates such as th ose described and set forth in this datasheet for semicond uctor die will vary de pending on a number of packaging, hand ling, use, and other factors. therefore sold die may not perform on an equivale nt basis to standard package products. note ? test conditions see table basic characteristics note ? moq: minimum order quantity product summary component i ra (a) ? (deg) 0.1 (nm) t330p 2.3 60 430 to 1100 ordering information ordering code packaging remarks package form t330p-sd-f wafer sawn on foil wi th disco frame moq: 55 000 pcs chip absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit reverse voltage v r 60 v junction temperature t j 100 c operating temperature range t amb -40 to +100 c storage temperature range t stg1 -40 to +100 c storage temperature range on foil t stg2 -40 to +50 c
t330p www.vishay.com vishay semiconductors rev. 1.2, 22-may-14 2 document number: 83490 for technical questions, contact: optochipsupport@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? the measurements are based on samples of die whic h are mounted on a to-header without resin coating basic characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - diode capacitance vs. reverse voltage fig. 2 - relative spectral sensitivity vs. wavelength note ? all chips are checked in accordance with the vishay semiconductor, specification of visual inspection fvov6870. the visual inspection shall be made in accordance with the specification of visual inspection as referenced. the visual inspe ction of chip backside is performed wi th stereo microscope with incident light and 40x to 80x magnification. the quality inspection (final visual inspection) is performed by production. an addition al visual inspection step as special re lease procedure by qm is not installed. basic characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit breakdown voltage i r = 100 a, e = 0 v (br) 60 v reverse dark current v r = 10 v, e = 0 i ro 0.1 3 na diode capacitance v r = 5 v, f = 1 mhz, e = 0 c d 1.3 pf reverse light current e e = 1 mw/cm 2 , = 950 nm, v r = 5 v i ra 2.3 a angle of half sensitivity ? 60 deg wavelength of peak sensitivity p 900 nm range of spectral bandwidth 0.1 430 to 1100 nm rise time v r = 10 v, r l = 50 , = 820 nm t r 4ns fall time v r = 10 v, r l = 50 , = 820 nm t f 4ns 0 2 4 6 8 0.1 c d - diode capacitance (pf) v r - reverse voltage (v) 94 8430 e = 0 f = 1 mhz 100 10 1 350 550 750 950 0 0.2 0.4 0.6 0.8 1.0 1150 94 8420 - wavelength (nm) s( ) rel - relative spectral sensitivit y mechanical dimensions parameter symbol min. typ. max. unit length of chip edge (x-direction) l x 0.67 mm length of chip ed ge (y-direction) l y 0.67 mm sensitive area a s 0.23 mm 2 wafer diameter d 100 mm die height h 0.265 0.28 0.295 mm bond pad anode x * y 0.1 x 0.1 mm 2 additional information frontside metallization, anode alsi backside metallization, cathode niv-ag dicing sawing die bonding technology epoxy bonding
t330p www.vishay.com vishay semiconductors rev. 1.2, 22-may-14 3 document number: 83490 for technical questions, contact: optochipsupport@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 handling and storage conditions ? the hermetically sealed shipment lots shall be opened in temperature and moistu re controlled cleanroom environment only. it is mandatory to follow the rules for disposition of ma terial that can be hazardous for humans and environment. ? product must be handled only at esd safe workstations. standard esd precaution s and safe work environments are as defined in mil-hdbk-263. ? singulated die are not to be handled with tweezers. a vacuum wand with non metallic esd pro tected tip shou ld be used. packing chips are fixed on adhesive foil. upon re quest the foils can be mounted on plastic frame or disco frame. for shipment, the wafers are arranged to stacks and hermeti cally sealed in plastic bags to ensure protection against environmental influence (humidity and contamination). use for recycling reliable operator s only. we can help getting in touch with your nearest sales office. by agreement we will ta ke back packing material, if it is sorted. you will have to bear the costs of transport. we will invoice you for any costs incurre d for packing material that is returned unsorted or which we are not obliged to accept.
legal disclaimer notice www.vishay.com vishay revision: 08-feb-17 1 document number: 91000 disclaimer ? all product, product specifications and data ar e subject to change with out notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of th e products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product , (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all implied warranties, includ ing warranties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain types of applicatio ns are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular applic ation. it is the customers responsibility to validate tha t a particular product with the prope rties described in the product sp ecification is suitable for use in a particular application. parameters provided in datasheets and / or specifications may vary in different ap plications and perfor mance may vary over time. all operating parameters, including ty pical parameters, must be va lidated for each customer application by the customer s technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death. customers using or selling vishay product s not expressly indicated for use in such applications do so at their own risk. please contact authorized vishay personnel to obtain writ ten terms and conditions rega rding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners. ? 2017 vishay intertechnology, inc. all rights reserved
|
